FEM based Optimization of stress and deformation of lap joint using different materials S275, Al6061 and EN8 through ANSYS & Minitab
Keywords:
Analysis of .Variance (ANOVA), Signal to Noise Ratio (SNR)Abstract
The objective of any industry is production of high quality products at low cost and increase the production rate. Welding is most important operation in any industry. It is essential to optimize the various parameters viz; welding current, welding speed, voltage, gas flow rate, etc. and also optimize mechanical properties viz stress , strain and deformation of welded joint . so that we can achieve the reliability, productivity and quality of the products. In this present study, the effective way is used to evaluate and optimise the welding techniques with better tensile strength for Lap Joint. The method opts for analysis of Lap welding joint is Taguchi method. Taguchi method is used for the purpose of result optimization. ANOVA method is used for proper judgement of result along with Taguchi method. The stress and deformation is calculated on the ANSYS software.
References
P. K. Singh, D. Patel, and S. B. Prasad, “Optimization of process parameters during vibratory welding technique using Taguchi ’ s analysis ଝ,” Perspect. Sci., pp. 2014–2017, 2016, doi: 10.1016/j.pisc.2016.04.088.
S. Umangkumar, C. Mehul, P. Jigar, and P. K. D. Bhatt, “Optimization of Welding Parameters Using Taguchi Method for Submerged Arc Welding of Conveyor Pulley Optimization of Welding Parameters Using Taguchi Method for Submerged Arc Welding of Conveyor Pulley,” no. April, 2015.
V. Mukhraiya, R. K. Yadav, and S. Jathar, “Parametric Optimisation of MIG Welding Process with the Help of Taguchi Method,” vol. 3, no. 1, pp. 1407–1410, 2014.
B. R. Borkar, “PROCESS PARAMETERS OPTIMIZATION IN FSW PROCESS USING TAGUCHI METHOD,” no. 4, pp. 551–558, 2018.
H. Li, P. O’Hara, and C. A. Duarte, “A two-scale generalized FEM for the evaluation of stress intensity factors at spot welds subjected to thermomechanical loads,” Eng. Fract. Mech., vol. 213, no. January, pp. 21–52, 2019, doi: 10.1016/j.engfracmech.2019.03.027.
M. Lepore, P. Carlone, F. Berto, and M. R. Sonne, “A FEM based methodology to simulate multiple crack propagation in friction stir welds,” Eng. Fract. Mech., vol. 184, pp. 154–167, 2017, doi: 10.1016/j.engfracmech.2017.08.024.
R. R. Patil and M. V Kavade, “Parametric Optimization of Gas Metal Arc Welding for S355J2N by Using Design of Experiment,” vol. 2, no. 10, pp. 44–48, 2015.
F. Y. Shu et al., “FEM modeling of softened base metal in narrow-gap joint by CMT+P MIX welding procedure,” Trans. Nonferrous Met. Soc. China (English Ed., vol. 24, no. 6, pp. 1830–1835, 2014, doi: 10.1016/S1003-6326(14)63260-X.
Y. H. P. Manurung et al., “Welding distortion analysis of multipass joint combination with different sequences using 3D FEM and experiment,” Int. J. Press. Vessel. Pip., vol. 111–112,
S. Umangkumar, C. Mehul, P. Jigar, and P. K. D. Bhatt, “Optimization of Welding Parameters Using Taguchi Method for Submerged Arc Welding On Spiral Pipes,” Int. J. Recent Technol. Eng., vol. 2, no. 5, pp. 50–54, 2013.
